LigninCorp » Industrial Knowledge » Lignosulfonate in Oil Drilling: Mud Thinners, FCLS and Chrome-Free Grades

Lignosulfonate in Oil Drilling: Mud Thinners, FCLS and Chrome-Free Grades

·

·

Multi-effect evaporator used to concentrate lignosulfonate liquor

Lignosulfonates are used in water-based drilling fluids (muds) mainly as thinners (deflocculants) and as aids to fluid-loss control. In a bentonite mud, clay platelets tend to link edge-to-face and form a gel. This raises viscosity and gel strength, especially as drilled solids, salt and temperature increase. Lignosulfonate adsorbs on the clay edges, adds negative charge and breaks this structure. Viscosity and yield point then fall, and the mud stays pumpable without adding more water.

Which lignosulfonate for which mud?

Product Typical role Key points from the TDS
Ferrochrome lignosulfonate (FCLS) Thinner and fluid-loss control agent for fresh-water and salt-water muds Lignosulfonate 55–60%, total Fe 4% max, total Cr 4% max, dry matter 95% min
Chrome lignosulfonate High-temperature thinner for deep wells and complex formations Total Cr 3.6–4.2%; dosage 0.5–1.0% (w/v) at mud pH 10.0–10.5; keeps mud properties at 150–160 °C for 16 h; tolerates salt contamination up to 2%
Chrome-free lignosulfonate Thinner and fluid-loss control where chromium is not acceptable Dosage 1.0% (w/v) in fresh-water mud and 2.0% in salt-water mud at pH 10.0–10.5; rated up to 150 °C

Performance in standard mud tests (TDS values)

Test mud FCLS Chrome LS Chrome-free LS
Fresh water, normal temp. (viscosity / reduction) ≤20 mPa·s / ≥85% ≤30 mPa·s / ≥85% ≤20 mPa·s / ≥85%
Fresh water, high temp. ≤30 mPa·s / ≥65% ≤40 mPa·s / ≥60% ≤35 mPa·s / ≥60%
Salt water, normal temp. ≤25 mPa·s / ≥70% ≤30 mPa·s / ≥65% ≤25 mPa·s / ≥65%
Salt water, high temp. ≤45 mPa·s / ≥55% ≤45 mPa·s / ≥60% ≤45 mPa·s / ≥45%

Values are from the current Green Agrochem TDS for each product (Rev. 2.0). They are measured in the supplier’s standard base muds, so check performance in your own mud with your own solids and salinity.

How lignosulfonate thinners are used

  • pH: lignosulfonate thinners work in alkaline muds. The TDS dosages assume a mud pH of 10.0–10.5, adjusted with caustic soda.
  • Addition: add as powder through the hopper or pre-dissolved in water. Add in steps and check rheology after each step.
  • Tests: run plastic viscosity, yield point, 10-second and 10-minute gel strength, and API fluid loss before and after hot-rolling at the expected bottom-hole temperature (API RP 13B-1 procedures).
  • Salt and calcium: salt-water and gypsum- or lime-treated muds normally need higher doses. The chrome grades are chosen when the mud must tolerate both high temperature and electrolyte contamination.

Chromium and environmental limits

FCLS and chrome lignosulfonate contain chromium. Many operators and jurisdictions restrict chromium in drilling fluids and cuttings discharge, especially offshore. Chrome-free lignosulfonate is the usual choice where the mud programme or permit does not allow chromium. Always follow the operator’s mud programme and local discharge rules.

Other oilfield uses

  • Dispersant and set retarder in oil-well cement slurries (selected sodium and calcium lignosulfonate grades).
  • Component of gel and plugging systems in some well-treatment formulations.

See the oil-well drilling fluids application page for the full product range. TDS, SDS, COA and samples: info@greenagrochem.com.

Reference

  1. Caenn R., Darley H.C.H., Gray G.R. Composition and Properties of Drilling and Completion Fluids, 7th ed. Gulf Professional Publishing, 2017 (chapters on clay chemistry and deflocculants).
  2. API RP 13B-1, Recommended Practice for Field Testing Water-based Drilling Fluids.